Server-technology PP02 Manual do Utilizador

Server Technology Inc. REMOTE Power On/Off TM+Aux INTELLIGENT RING-ACTIVATED REMOTE POWER CONTROL Installation and User's Guide for:

LINE port - the incoming telephone line, from the wall-jack, connects to this RJ11 port. MODEM port - a telephone cable connects out from this R

A sample session, Power-ON Mode: 1 The user makes a modem call to the phone number of the line attached to the Power On/Off +Aux control unit. 2 The

Installation This section covers the initial installation and testing of the Power On/Off +Aux control unit and the Intelligent Power Module (110vAC v

NOTE: UPS users must attach the wall-mount power supply to a second backed-up outlet provided on the back of the battery back-up. If not, a power ou

After installing Remote Power On/Off: PCOFF ONON OFFPower/Surge StripTelephone CablesToModemLine-InTelephoneWall JackModemPowerSupplyON OFFOFFONMRTRSD

Operating Modes and Options Remote Power On/Off offers three exclusive Operating Modes with several selectable options for each mode. Operating mode

Power-ON Mode The default operating mode for the Remote Power On/Off system is the Power-ON Mode. This mode allows a PC and peripherals to be turned

Note: These Power-OFF Delay Time settings are useful to support post-connection operations, such as host software "Call-Back" services.

Power-OFF Delay Time DIP switches 3 and 4 are used to select the Power-OFF Delay Time value: 3|OFF 4|OFF 1 second Power-OFF Delay Time * 3|OFF

Example DIP Switch Configurations, Power-ON Mode: Ring = Power-ON, Hang-up = Power-OFF 1 RING Power-ON1 second Power-OFF delay1 RING Power-ON2 minute

Table of Contents Introduction 5 About this Guide 6 Product Overview 7 Intelligent Power Module (IPM) 8 Power On/Off +Au

REBOOT Mode The second operating mode is the REBOOT Mode. This mode is used to remotely reboot a device by temporarily interrupting its power source.

No Answer REBOOT With the No Answer REBOOT method, the Power On/Off +Aux control unit will count incoming RINGs and only initiate a reboot when a sele

This On-Hook REBOOT method does not require any changes to the host PC configuration (the modem can answer on any ring number desired). For example,

Off-Hook (busy) REBOOT Option The one condition that can block you from initiating an immediate reboot with Remote Power On/Off is an endless busied-o

Selecting the REBOOT Method DIP-switch 5 selects between the No Answer REBOOT and the On-Hook REBOOT methods: 5|OFF On-Hook REBOOT Method 5|ON

Example DIP Switch Configurations, REBOOT Mode: Power is normally ON; REBOOT = Power-OFF, 30 second delay, Power-ON. No Answer reBOOTMi

Infinite-On/Off Mode The Power-ON Mode allows a device to be turned on, remain on for the duration of the call, but always automatically turned back o

DIP Switch Configuration The following outlines the DIP switch positions for the Infinite-On/Off Mode. When the Infinite-On/Off option is enabled, th

+Aux Feature The +Aux feature allows a single telephone line to be shared by a modem, the Power On/Off +Aux system, and one other telephone device, su

Sharing a Single Phone Line The Power On/Off +Aux control unit, using relays, achieves line-sharing by controlling when the LINE port is continuous to

Off-Hook (busy) REBOOT 23 DIP Switch Configuration, REBOOT Mode 23 Example DIP Switch Settings, REBOOT Mode 25 Infinite-On/Off Mod

Modem Priority Option The +Aux Feature has been designed to optionally allow priority to be given to the modem whenever the PC is fully booted and rea

Sample Sessions The following sample sessions are common end-user configurations. They are provided as a guideline to better understand the possible

1 2 3 4 5 6 7 8ON Power-ON Mode, +Aux feature Enabled Power-ON Ring 5; 2 minute Power-OFF delay. Popular configuration for secure power cont

1 2 3 4 5 6 7 8ON Power-ON Mode Power-ON Ring 1; 15 minute Power-OFF delay. Configuration for using the PC (with fax/modem) as a facsimile m

1 2 3 4 5 6 7 8ON REBOOT Mode, Power is normally ON No Answer REBOOT Method; minimum rings required to effect a reboot = 1 2-hour Off-Hook (b

1 2 3 4 5 6 7 8ON Infinite-On/Off Mode 1 Ring/Hang-up to 'prime', wait 10 seconds then place second call: 5 RINGs to Power-ON, or

Appendix A ON/OFF and STATUS LED Activity The front panel of the Power On/Off +Aux control unit contains two indicator lights. These LEDs inform the

• ON ~ The power is ON and the REBOOT function is disabled. Incoming calls cannot initiate a remote reboot. LED is ON. • OFF ~ A REBOOT is in prog

Power-ON and Infinite-On/Off Modes In the Power-ON and Infinite-On/Off operating modes, the idle (ON-HOOK) state of the STATUS LED will indicate whe

220 VAC Intelligent Power Module Overview/Installation For users that have purchased the 220VAC version of Remote Power On/Off, the Intelligent Power

Functional Changes for ShutDown Support 49 Microsoft Windows NT UPS Service Configuration 50 Microsoft Windows 2000/XP UPS Service Con

Step 2 Locate the included cable-mount IEC 320 /C14 male inlet connector assembly (illustrated below) and a multiple outlet power or surge-protection

C Loosen each screw on the three terminals, then attach the appropriate conductor to each, and tighten the screws. Be sure to attach each conductor

Appendix B - Windows 95/98/ME ShutDown Introduction Windows 95, Windows 98, and Windows Millennium Edition must be shut down prior to turning off pow

The following diagram shows a complete installation with the Y-cable and ShutDown adapters. This diagram replaces the "After installing Remote P

Functional Changes to the Remote Power On/Off Due to the modified firmware in the Power On/Off +Aux ShutDown/REBOOT control unit, there are some minor

Starting with the power OFF and the LED off, pressing the button once will turn power ON and the LED will go on green. Pressing the button a second t

The first time AutoShutDown runs, it will prompt you to choose the port to which the ShutDown adapter is attached and to enable it. Once you have don

Appendix C - Windows NT/2000/XP ShutDown Introduction Windows NT, Windows 2000 and Windows XP must be shut down prior to turning off power. When a u

The following diagram shows a complete installation with the Y-cable and ShutDown adapter. This diagram replaces the "After installing Remote Po

Functional Changes to the Remote Power On/Off Due to the modified firmware in the Power On/Off +Aux ShutDown/REBOOT unit, there are some minor functio

Introduction Congratulations on your purchase of Remote Power On/Off. Built with pride in the United States of America it allows an unmanned PC and/o

Starting with the power OFF and the LED off, pressing the button once will turn power ON and the LED will go on green. Pressing the button a second t

Remote Power On/Off for Windows NT, model #PPNT, makes use of the UPS Service much the same way as a UPS does. Whenever Remote Power On/Off is going

2) Choose the options as illustrated below, then click OK: 3) To configure the UPS Service for the proper COM port and operating parameters of the R

Windows 2000/XP UPS Service Configuration Windows 2000 and Windows XP, similar to Windows NT, includes a service for an Uninterruptible Power Supply (

The Power Options Properties screen will appear. Click the UPS tab. The Power Options Properties screen will appear similar to the screen capture do

4) On the UPS Interface Configuration screen (shown below, left), enable the UPS Signal Polarity options as illustrated. Click ‘Finish’ to return t

Operational Behavior, Windows 2000/XP ShutDown Configured as shown in the previous screen shots, and after a call initiates a power-OFF or a REBOOT, t

To test the UPS Service, insert the loopback plug into the RJ11 end of ShutDown adapter. Within 15 seconds of insertion, the first warning message fr

Windows NT/2000/XP Automatic Logon When a Windows NT system boots, the operating system expects a local user to press the <Ctrl><Alt><D

Appendix D - Upgrade Kits Server Technology offers three distinct versions of Remote Power On/Off +Aux: 1) Model #PP02, a non-shutdown version ideal

About this Guide This guide is intended to be printed. Printing this guide will provide proper clarity of the diagrams. Remote Power On/Off has bee

Is Your Power On/Off Control Unit Upgrade-Compatible? Only "+Aux" versions of Remote Power On/Off are capable of being upgraded. "+Aux

• Check position U2 on your unit. This is the location of the ROM chip. Is the ROM chip in a socket (removable), or is the ROM chip soldered direct

4) Identify the correct direction to insert the new Upgrade ROM into the socket. Look at the socket on the circuit board. Make note that one end of

FCC Compliance Information Notification To The Telephone Company This equipment complies with Part 68 of the FCC Rules. The REN is useful to determine

Specifications Power On/Off +Aux Control Unit Interface Specifications Line, Modem, Aux and IPM Ports: 6 wire modular RJ11C Telephone Ringer Equivale

Warranty & Support Warranty and Limitation of Liability Server Technology, Inc. agrees to repair (parts & labor) or replace Products that fail

Product Registration Registration is your key to special offers and services reserved for Registered Users. • Excellent Technical Support Services •

Remote Power On/Off Warranty & Support • 67 Return Merchandise Authorization If you have a unit

Product Overview Pictured below are the components included with a 110VAC Remote Power On/Off system. The items in the center picture represent a PP0

Intelligent Power Module (IPM) - 110vAC model The Intelligent Power Module houses an electronic relay that will switch power to your computer, or any

Power On/Off +Aux Control Unit The desktop portion of Remote Power On/Off is the Power On/Off +Aux control unit. This unit monitors the telephone l